|  |  | | Even 0.5mm holes may be drilled. With three step pulleys. | |  |  |
|
| | |  | | Small and accurate. Ideal for Drill stand MB 140/S and Drill press TBM 220. | | | |
|
|
| |  | | For 50mm discs and brushes. With electronic speed control from 8 to 24 m/sec. | | | |
|
| | |  | | Steel wire brush for de-rusting and cleaning steel and NF metals. | | | |
|
|
| |  | Corundum (grade N) with 12.7mm bore
No 28308 | | | |
|
| | |  | Silicon carbide with 12.7mm bore. Soft compound for very hard materials.
No 28310 | | | |
|
|
| |  | | Table moveable through 45°, allowing mitre cuts. | | | |
|
| | |  | | Made of ceramic compound: 50% alu oxide and 50% silicon carbide. | | | |
|
|
| |  | | Easy sharpening of drill bits from 3 to 13mm diameter, standard 118°. | | | |
|
| | |  | | These adapters extend the BSG 220's range to cover 1.5 - 3mm. | | | |
|
|
| |  | | For drill shank sizes 0.5 to 6.0mm. | | | |
|
| | |  | | Small and beautiful: the accurate miller for lab technician, optician, jeweller, electronic/model builder. | | | |
|
|
| |  | | This accessory is used to drill offset holes, holes with equal spacing as well as milling key surfaces in 4 sided, 6 sided, etc materials. | | | |
|
| | |  | | These double flute cutters are made from solid tungsten, clockwise cutting. | | | |
|
|
| |  | | Completely angular. Jaw width 46mm, clamping capacity 30mm. Total length 70mm. | | | |
|
| | |  | | Perfect cuts in steel, non-ferrous metals, wood and plastic. Even cuts glass and ceramics with diamond blade. | | | |
|
|
| | | | Triple ball bearing system with feed pipe for coolant when used with the diamond blade. | | | |
|
| | | | | Swedish steel 1,065 x 5 x 0.4mm. Fine toothed (24TPI). For steel and brass. | | | |
|
|
| | | | | Extra narrow for tight curves (1,065 x 3.5 x 0.5mm). Coarse toothed (14TPI). | | | |
|
|
| | | | For cutting ceramics, glass and fibreglass. 1,065 x 3 x 0.3mm. | | | |
|
| | |  | | With electronically controlled speeds between 250 and MICROMOT 750rpm. Ideal for wet sanding. | | | |
|
|
| |  | | Made of plastic. With stop cock and regulator. | | | |
|
| | |  | | Size 420 x 310 x 15mm. Includes gasket for sealing the fixing holes of the machine. | | | |
|
|
| | | | Industrial quality. Carborundum with resinoid bond. | | | |
|
| | | | | Industrial quality. Carborundum with resinoid bond. | | | |
|
|
| | | | Industrial quality. Carborundum with resinoid bond. | | | |
|
| | | | | Silicon carbide with resinoid bond, usable on NF metals, steel, glass, PC cards, plastic and ceramic. | | | |
|
|
| |  | | For clean, safe cutting to length of NF metals, plastic and wood. | | | |
|
| | |  | | The high tooth count yields clean cuts when cutting a variety of materials, e.g. balsa, plywood, soft wood and PC cards. | | | |
|
|
| |  | | Corundum compound, used on steel, NF metal, plastic and wood. | | | |
|
| | |  | | Quiet and accurate. Ideal for the lab, workshop and MICROMOT delicate operations. | | | |
|
|
| |  | | Triple slit and hardened. One each of 2.35 - 3.0 - 3.2 - 4.0 - 5.0 and 6.0mm. | | | |
|
| | | | | Two T nuts and cap screws with washers. Used on BFB 2000, KT 150 and TBH. | | | |
|
|
| |  | | Precision vices. Exhibit feed, ease of operation and accuracy | | | |
|
| | | | | Precision vices. Exhibit feed, ease of operation and accuracy | | | |
|
|
Tabletop Tools & Accessories Metalworking
